Help center
Guides and how-tos
Clear, step-by-step help for pressing, file prep and care. Pick a topic or search.
-
Ordering
How to build a gang sheet that saves money
Plan your designs, pick the right length and fill every inch of film.
-
Pressing
How to press DTF with a heat press
Temperature, time, pressure and placement for a clean, long-lasting press.
-
Pressing
How to press DTF with a Cricut EasyPress
Small batches and single shirts, with firm, even pressure.
-
-
-
No guides match your search yet. Try another word.
FAQ
Quick answers
The questions we hear most, in one place.
What is DTF printing?
DTF stands for direct-to-film. Your design is printed onto a clear film, backed with white ink and a fine adhesive powder, then cured. You heat press it onto fabric, peel the film away and the print stays: soft, stretchy and bright on any color.
How is DTF different from sublimation or vinyl?
Sublimation only works on light-colored polyester. Vinyl has to be cut, weeded and layered one color at a time. DTF prints every color at once and presses onto cotton, polyester and blends, light or dark.
What is a gang sheet?
One 22″ wide sheet that you fill with as many designs as you like, in any mix of sizes. You pay for the length of the sheet, not per design, so it's the best value when you need more than a few transfers.
Should I use the builder or upload my own sheet?
Use the builder if you have separate design files. It arranges them on the sheet for you. Upload a sheet if you've already laid everything out on a 22″ wide canvas in your design software.
Is there a minimum order?
No. Order a single transfer or a thousand.
What files can I upload?
PNG with a transparent background prints best. We also accept JPG, PDF, AI, PSD and SVG.
What resolution do I need?
300 DPI at the size you're printing. A 10″ wide design should be about 3,000 pixels across. Low-resolution files can print blurry or pixelated.
Do I need to remove the background?
Yes, unless you want it printed. Anything that isn't transparent, including white, prints as part of your design.
Will the colors match my screen?
Very closely. Screens give off light and ink doesn't, so expect small differences, especially with neon and very bright colors.
What size should my design be?
A good starting point: 10–12″ wide for an adult full front, 8–10″ for a youth front, 3–4″ for a left chest and 2–2.5″ for hats and sleeves. When in doubt, hold a ruler up to the garment.
Where should I place my design?
On an adult shirt, the top of the design sits 4–5″ below the collar, on the front and the back. Measure down from the round bottom edge of the collar, not the shoulder seam, so the design sits fully below it.
How do I apply a DTF transfer?
Preheat the garment for 5 seconds. Place the transfer adhesive side down with the top of the design 4–5″ below the collar. Press at 300–320°F with medium-firm pressure for 10–15 seconds, then peel the film while it's hot. Our pressing guides cover every step.
Can I use an EasyPress or a home iron?
Yes. With an EasyPress, press at 300°F for 10–15 seconds with firm, even pressure on a hard surface. With a home iron (set to cotton, no steam), hold it still for about 20 seconds per section. Our guides walk you through each one.
Can I press onto polyester or nylon?
Yes, with less heat. Start at about 275°F for around 7 seconds. Too much heat can leave press marks or make polyester dye bleed into the print. Nylon with a water-resistant coating may need a special adhesive, so press a test piece first.
Do transfers work on dark fabric?
Yes. Every print has a white underbase, so colors stay bright on black and other dark garments.
How long do DTF prints last?
50+ washes when pressed and cared for properly. Wash inside out in cold water, tumble dry low and skip the bleach.
How should I store unused transfers?
Flat, in a cool, dry place, away from direct sunlight.
No questions match your search. Try another word, or ask us directly.
ready, set, press
Got a design? Let's press it.
Start a gang sheet in minutes. No minimums, no setup fees.
